Skip to content

Pace Calculator

Find your pace from a time and distance, your finish time from a target pace, or how far you will go, with race times and splits.

Health & FitnessUpdated Free · No sign-up

How to use the Pace Calculator

  1. Pick what you want to work out using the tabs: Pace, Time or Distance.
  2. Enter Time (h:mm:ss).
  3. Choose Distance.
  4. Choose Units.
  5. Read your answer in the results panel. It updates as you type, and the breakdown, step-by-step working and any charts or tables appear below it.
  6. Use Share link to save or send the exact calculation, or Copy to paste the results elsewhere.

Pace, time and distance

Pace is the time it takes to cover one unit of distance, written as minutes and seconds per kilometre or per mile. It is the inverse of speed: runners think in pace because it tells you directly how long each kilometre or mile should take. The three quantities are linked by one relation, so if you know any two you can find the third.

pace = time ÷ distance    time = pace × distance    distance = time ÷ pace

Enter times as h:mm:ss (1:45:30) or mm:ss (25:00) and paces as mm:ss. Choose a race distance or type your own.

Worked example

You ran 10 km in 50:00. Your pace is 3,000 seconds ÷ 10 km = 300 seconds, or 5:00 per kilometre. A mile is 1.609344 km, so the same effort is 5:00 × 1.609344 = 8:02.8, shown as 8:03 per mile. Your speed is 10 km ÷ (50/60) h = 12 km/h, or about 7.46 mph. Holding that pace for a marathon (42.195 km) would take 42.195 × 5:00 = 3:30:59.

Using the race and split tables

The race table shows what your current pace means over common distances: a mile, 5K, 10K, half marathon and marathon. These are even-pace times, not race predictions. Most people slow down over longer distances, so a 50-minute 10K runner would typically run a marathon nearer 3:50 than 3:31. If you want a prediction, add roughly 5% to the time for every doubling of distance as a rule of thumb.

The split table lists the time for each kilometre or mile and the elapsed time at each marker, so you can write splits on your wrist or programme a watch. A final partial split is shown for distances that are not a whole number.

Tips for pacing

  • Start slightly slower than goal pace for the first kilometre or two; going out too fast is the most common racing mistake.
  • Hills, heat and wind all cost time. Judge effort, not just pace, on difficult courses.
  • Easy training runs are usually 60 to 90 seconds per kilometre slower than 10K race pace.

All figures are estimates for training and planning, not medical advice. Check with a doctor before starting a hard training plan if you have a health condition.

Frequently asked questions

How do I calculate my running pace?

Divide your total time by the distance. 25 minutes for 5 km is 25 ÷ 5 = 5 minutes per kilometre. The calculator handles the minutes-and-seconds arithmetic and converts between km and miles.

What pace do I need for a sub-4-hour marathon?

About 5:41 per kilometre or 9:09 per mile, held evenly for 42.195 km. Most runners aim a few seconds faster to leave a buffer for water stops and fatigue.

How do I convert pace per km to pace per mile?

Multiply the pace per kilometre by 1.609344. For example, 5:00 per km is 8:03 per mile. To go the other way, divide pace per mile by 1.609344.

What is a good 5K time?

It depends on age, sex and training. Many recreational runners finish between 25 and 35 minutes; under 20 minutes is a strong club-level time.